Code
0711
Description
Precious decorative finish, which has a metallic sheen, based on acrylic resins in water emulsion with an excellent resistance to washing and a high flexibility in application and dilatation, for internal spaces.
Use
It can be applied to wall surfaces, properly prepared with concrete, where a luminescent aesthetic appearance combined with excellent resistance to washing with cleansing agents are required.
Appearance of the film
Metallic
Color
Color chart
Component
1
Hardening
Physical hardening through evaporation of water and union of the polymer
Specific weight
From 1,03 gr/m
VOC
40 gr/ liter
Minimum thickness
50 -60 micron
Estimated yield
4-5 m² / kg for a thickness of 50 microns
Flash point
Component A > 114°C
Temperature resistance
Max 60° C
Preparation of surfaces
New surfaces:
Apply a coat of our insulating product « IMPRIMITURA ACRILICA » diluted with water in ratio 1 to 5 (mix each liter of « IMPRIMITURA ACRILICA » with 5 liters of water).
Old surfaces:
Remove any parts that are peeling off and, after a careful cleaning of the substrate, apply a coat of our insulating product « IMPRIMITURA ACRILICA » diluted with water in ratio 1 to 5 (mix each liter of « IMPRIMITURA ACRILICA » with 5 liters of water).
Apply a coat of our insulating product « IMPRIMITURA ACRILICA » diluted with water in ratio 1 to 5 (mix each liter of « IMPRIMITURA ACRILICA » with 5 liters of water).
Old surfaces:
Remove any parts that are peeling off and, after a careful cleaning of the substrate, apply a coat of our insulating product « IMPRIMITURA ACRILICA » diluted with water in ratio 1 to 5 (mix each liter of « IMPRIMITURA ACRILICA » with 5 liters of water).
Preparation of the product
It is ready to use. Mix the product before the use.
Component A 100
Component A 100
Environmental conditions
Ambient temperature: from + 5 to 40° C
Temperature of the support: > 10° C
Humidity: 0 - 85 %
In order to prevent the formation of condensation, it is necessary that the temperature of the substrate is at least 3° C above the dew point.
Temperature of the support: > 10° C
Humidity: 0 - 85 %
In order to prevent the formation of condensation, it is necessary that the temperature of the substrate is at least 3° C above the dew point.
Drying and hardening time
For the thickness of 50 microns 10° C 20° C 30° C
Dry to touch 3 1 0,5 hours
Dry in depth 8 4 - 5 2 hours
Dry to touch 3 1 0,5 hours
Dry in depth 8 4 - 5 2 hours
Time of overpainting
Minimum (hours) 10° C 20° C 30° C
8 4 3 hours
Maximum unlimited in the absence of contaminants
8 4 3 hours
Maximum unlimited in the absence of contaminants
Application
After an appropriate preparation of the substrate, apply the product as follows: apply a coat of our white primer « SABBIAFOND » with brushes or roller diluted with water to 20 - 25 %. In order to obtain a color of our chart, mix in the amount shown on our chart LINEA PLATINUM of our paste TONER.
First coat: apply « DELICATO », not diluted, with a brush. On the surface, the brush strokes must be crossed avoiding painting the same position in the same way.
Second coat: after 6 hours, apply a second coat, in the same way, in order to obtain wonderful contrasts of light.
First coat: apply « DELICATO », not diluted, with a brush. On the surface, the brush strokes must be crossed avoiding painting the same position in the same way.
Second coat: after 6 hours, apply a second coat, in the same way, in order to obtain wonderful contrasts of light.
Shelf life
2 years in a cool and dry place (max 40° C)
Packs
Comp A Kg. 2 - Kg. 5.