Code
1012
Description
Thick and liquid coating, waterproof, UV - resistant, based on special elastomeric resins and glass hollow microspheres of 3M that allow the product to be included in the category of Cool Roof products, that is with a high solar reflectance and a high reduction in thermal conductivity.
Use
It is suitable for waterproofing concrete artifacts, foundations, parts of the wall that is not slightly seen below the surface of the road, fibre cement, bituminous coverings, galvanized sheet.
Appearance of the film
Matt
Color
White
Component
1
Hardening
Physical hardening through evaporation of water and union of the polymer
Specific weight
From 1,290 - 1320 gr/ml
Volume of solids
57 %
VOC
120 gr/ liter
Minimum thickness
500 micron
Estimated yield
1,1 m² / litre for a thickness of 500 microns
Flash point
Component A: > 114°C
Reflection percentage
White 83 % for a thickness of 150 microns
Elongation %
ASTM 522 32%
Preparation of surfaces
Perform an accurate cleaning to remove dirt, any parts that are peeling off, grease and other contaminants. Prime with our primer for Resinguaina (base pliolite) or our primer with water « H595 IMPRIMITURA ».
The surface must be dry; the presence of excessive humidity inside the substrate, in the process of solar radiation, can generate vapour that causes the formation of bubbles and the next detachment of the coating.
The surface must be dry; the presence of excessive humidity inside the substrate, in the process of solar radiation, can generate vapour that causes the formation of bubbles and the next detachment of the coating.
Preparation of the product
Mix the product before the use.
If you use the spatula, the product shouldn’t be diluted.
If you use the roller or the brush, you have to dilute the product by 10 to 15 % with water
If you use the spatula, the product shouldn’t be diluted.
If you use the roller or the brush, you have to dilute the product by 10 to 15 % with water
Environmental conditions
Ambient temperature: from + 5 to 40° C
Temperature of the support: > 10° C
Humidity: 0 - 85 %
In order to prevent the formation of condensation, it is necessary that the temperature of the substrate is at least 3° C above the dew point.
Temperature of the support: > 10° C
Humidity: 0 - 85 %
In order to prevent the formation of condensation, it is necessary that the temperature of the substrate is at least 3° C above the dew point.
Drying and hardening time
For the thickness of 500 microns 10° C 20° C 30° C
Dry to touch:
10°C: 24 hours
20°C: 6 hours
30° C: 1 hours
Dry in depth:
10°C: 24 hours
20° C: 8 hours
30° C: 2 hours
Dry to touch:
10°C: 24 hours
20°C: 6 hours
30° C: 1 hours
Dry in depth:
10°C: 24 hours
20° C: 8 hours
30° C: 2 hours
Time of overpainting
Minimum (hours):
10° C: 24 hours
20° C: 8 hours
30° C: 3 hours
Maximum unlimited in the absence of contaminants
10° C: 24 hours
20° C: 8 hours
30° C: 3 hours
Maximum unlimited in the absence of contaminants
Application
Roller, Brush
If you use the roller, you have to use medium - haired rollers or rollers with alveolar sponges
If you use the roller, you have to use medium - haired rollers or rollers with alveolar sponges
Shelf life
1 year in a cool and dry place (max 40° C)
Packs
Comp A Lt. 14 Lt. 5 Lt. 2,5