ELASTOSIOLX
Siloxanic elastomeric painting
Excellent breathability and water repellency
Alkali-resistant and weatherproof
Code
0860
Description
It is an emulsion paint based on acrylic resins and siloxane modified on elastomeric copolymer, anti-mildew and anti-algae, which give the product an excellent water repellence, an excellent permeability to water vapour and moisture, a high resistance in alkaline environments and an excellent permanent elasticity.
Use
To protect surfaces prepared with lime plaster or cement, or facades containing cracks, when you want a good weather resistance, combined with good breathability and water repellency. It adheres well even on old paints if they are well adherent.
Aspect of the film
Matt
Colour
White and from colour chart
Component
1
Hardening
Physical hardening by evaporation of water and coalescence of the polymer.
Specific weight
From 1,360 – 1,410 gr/m
Volume of solids
45,5 %
VOC
12 gr/ liter
Minimum thickness
80 micron
Theoretical yield
5,6 m² / l for a dry thickness of 80 microns
Flash point
Component A > 114°C
Capillary Absorption
DIN 52615: Sd=0,14 m
Adhesion
ISO 2409: Excellent
Chalking
ISO 4628-6: Excellent
Temperature resistance
Max 60°C
Vapor permeability
ASTM D 1653-72: 752,2 g/mq d; 1988,6 g/mq d (Interpolated value of the support)
Washability
> 10000 Strokes
Surface preparation
New surfaces:
New plaster or patching must be aged, clean, dry and without chalking. Then apply a coat of fixative SILOX PRIMER.
On old paints eliminate traces of oil, grease, loose parts, level any irregularities in the surface, seal any cracks.
Then apply a coat of fixative SILOX PRIMER.
If mildew is present, clean the support with our SD SPRAY ANTIMILDEW, then apply a coat of SANIMUFF sanitizing solution.
New plaster or patching must be aged, clean, dry and without chalking. Then apply a coat of fixative SILOX PRIMER.
On old paints eliminate traces of oil, grease, loose parts, level any irregularities in the surface, seal any cracks.
Then apply a coat of fixative SILOX PRIMER.
If mildew is present, clean the support with our SD SPRAY ANTIMILDEW, then apply a coat of SANIMUFF sanitizing solution.
Preparation of the product
Mix the product before use and add water
Component A 100
Water: 1st coat 25-30% - 2nd coat 10-15%
Component A 100
Water: 1st coat 25-30% - 2nd coat 10-15%
Environmental conditions
Room temperature: from + 8 to + 40°C
Surface temperature: > of 10°C
Humidity: 0 – 85 %
To prevent the formation of condensation is necessary that the temperature of the substrate is at least 3 ° C above the dew point.
Surface temperature: > of 10°C
Humidity: 0 – 85 %
To prevent the formation of condensation is necessary that the temperature of the substrate is at least 3 ° C above the dew point.
Precautions:
. Do not apply on wet or insufficiently aged substrates
. Do not apply at temperatures below 10 ° C
. Do not apply with greater than 85% humidity, in case of imminent rain and in the presence of wind.
. Do not apply at temperatures below 10 ° C
. Do not apply with greater than 85% humidity, in case of imminent rain and in the presence of wind.
Drying time and hardening
For thickness of 100 microns 10°C 20°C 30°C
Dry to the touch 3 1 0,5 ore
Through drying 12 8 4
Dry to the touch 3 1 0,5 ore
Through drying 12 8 4
Waiting times for overcoating
Minimum (hours) 10°C 20°C 30°C
24 12 8
Maximum unlimited in the absence of contaminants
24 12 8
Maximum unlimited in the absence of contaminants
Application
Brush, roller or spray
For brush application, use nylon brushes or pure bristle brushes.
For roller application using a medium-haired roller.
For the application, use the method of crossed coats
For brush application, use nylon brushes or pure bristle brushes.
For roller application using a medium-haired roller.
For the application, use the method of crossed coats
Storage life
Two years in a cool, dry place (max 40 ° C)
Packaging
Comp A Lt. 14 – Lt. 5 – Lt. 2,5