Code
0614
Description
RESINFLEX F is a one-component elastic fibrous primer based on modified acrylic resins and selected mineral fillers, specifically formulated for the preparation of surfaces subject to micro-cracking, thermal expansion and structural movement, prior to the application of protective and decorative coatings. The presence of synthetic fibres gives the product excellent reinforcing and crack resistance properties.
Use
The product can be used to give an intermediate filling coat on new or old restored plasters, concrete or cracked surfaces as long as they adhere. If the cracks are widespread, the use of a fiberglass mesh is recommended.
Film appearance
Matt
Colour
White and Colour Chart
Component
1
Hardening
Physical by evaporation of water and coalescence of the polymer.
Specific weight
From 1,45 +/- 0,05 kg/l UNI EN ISO 2811-1
Volume of solids
65 +/2 2% UNI EN ISO 3251
VOC
16 g/l (Cat. A/c)
Minimum thickness
20 micron
Theoretical yield
0,300 kg/mq. For a thickness of 200 microns dry
Flash point
Component A > 114°C
Extension %
>200 for a dry thickness of 500 microns
washability
> 10000 hits
Preparation of the surfaces
The substrate must be clean, dry and free of loose parts. Remove any efflorescence and fill cracks and fissures larger than 2 mm with our ELASTUK elastic fibre putty. On very absorbent or crumbling substrates, apply a coat of our consolidating sealer H95 PRIMER.
Preparation of the product
Mix the product thoroughly before use.
For roller applications dilute with max. 5% clean water.
The product is ready to use
Do not add any other solvents or additives.
For roller applications dilute with max. 5% clean water.
The product is ready to use
Do not add any other solvents or additives.
Environmental conditions
Ambient temperature: from + 5 to 40°C
Temperature of the surface: > 10°C
Humidity: 0 – 85 %
To prevent the formation of condensation the temperature of the surface
must be at least 3°C higher than the dew point.
Temperature of the surface: > 10°C
Humidity: 0 – 85 %
To prevent the formation of condensation the temperature of the surface
must be at least 3°C higher than the dew point.
Drying and Hardening
10°C: 24 hours touch, 24 hours deep
20°C: 6 hours touch, 8 hours deep
30°C: 1 hour touch, 2 hours deep
20°C: 6 hours touch, 8 hours deep
30°C: 1 hour touch, 2 hours deep
overpainting
Minimum (hours): 10°C - 24 hours; 20°C - 8 hours; 30°C - 3 hours
Application
Brush, roller.
For roller applications use medium-haired or honeycomb rollers
For roller applications use medium-haired or honeycomb rollers
Shelf life
1 year in a cool ad dry place (max 40°C)
Packs
Comp A Kg. 20; Kg. 5
Adhesion on concrete
> 1.5 N/mm (cohesive fracture)
Resistance to carbonation
Classe CO2-1
Frost/thaw resistance
25 cycles without alterations
Viscosity
18.000 +/- 2.000cP
pH
8,5 +/- 0,5
UV resistance
Excellent
Vapour permeability
Class V2 UNI EN 1062-1
Heavy rain resistance
Class W3 UNI EN 1062-3
Warnings and Precautions
Do not apply on damp substrates or with rising damp.
Avoid application in direct sunlight or strong wind
Protect from rain for at least 6 hours after application
Temperatures below +5°C slow drying
Clean tools immediately with water
Avoid application in direct sunlight or strong wind
Protect from rain for at least 6 hours after application
Temperatures below +5°C slow drying
Clean tools immediately with water
Conservation and Storage
Store in a cool, dry place (5-25°C)
Protect from frost
Keep away from heat sources
Protect from frost
Keep away from heat sources
Security
Consult safety data sheet before use
Use appropriate PPE
Avoid contact with eyes and skin
Keep out of reach of children
Use appropriate PPE
Avoid contact with eyes and skin
Keep out of reach of children
Disposal
Dispose of waste according to local regulations. Empty containers can be disposed of in separate collection after careful emptying.
The information contained in this data sheet is based on our current technical and scientific knowledge. The data given refer to tests carried out under standard laboratory conditions and may vary depending on actual application conditions.