Code
0714
Description
Putty based on acrylic resins in aqueous emulsion and special pigments that give the product some particular effects typical of gold and silver. PERLA is a washable product
Use
It can be applied on suitably prepared concrete wall surfaces where a pearlescent aesthetic appearance is required combined with excellent resistance to washing with detergents.
Appearance of the film
Pearlescent
Colour
Colour chart
Component
1
Hardening
Physical by evaporation of water and coalescence of the polymer.
Specific weight
From 1,03 gr/m
VOC
40 gr/ liter
Minimum thickness
50 -60 micron
Estimated yield
4-5 m² / kg for a thickness of 50 microns dry
Flash point
Component A > 114°C
resistance to temperature
Max 60°C
Preparation of surfaces
New surfaces:
Apply one coat of our IMPRIMITURA ACRILICA insulator diluted with water in a ratio of 1 to 5 (for each liter of IMPRIMITURA ACRILICA mix 5 liters of water).
Old surfaces: remove all the peeling parts, and after a careful cleaning of the surface, apply a coat of our ACRYLIC IMPRIMITURA diluted with water in a ratio of 1 to 5 (for each liter of ACRYLIC IMPRIMITURA mix 5 liters of water).
Apply one coat of our IMPRIMITURA ACRILICA insulator diluted with water in a ratio of 1 to 5 (for each liter of IMPRIMITURA ACRILICA mix 5 liters of water).
Old surfaces: remove all the peeling parts, and after a careful cleaning of the surface, apply a coat of our ACRYLIC IMPRIMITURA diluted with water in a ratio of 1 to 5 (for each liter of ACRYLIC IMPRIMITURA mix 5 liters of water).
Preparation of the product
Ready to use. Mix the product before use.
Component A 100
Component A 100
Environmental conditions
Ambient temperature: from + 5 to 40°C
Temperature of the surface: > 10°C
Humidity: 0 – 85 %
To prevent the formation of condensation the temperature of the surface
must be at least 3°C higher than the dew point
Temperature of the surface: > 10°C
Humidity: 0 – 85 %
To prevent the formation of condensation the temperature of the surface
must be at least 3°C higher than the dew point
Drying and hardening
For thicknesses of 50 microns 10°C 20°C 30°C
Dry to touch 3 1 0,5 hrs
Dry in depth 8 4 -5 2
Dry to touch 3 1 0,5 hrs
Dry in depth 8 4 -5 2
overpainting
Minimum (hours) 10°C 20°C 30°C
8 4 3
Maximum Unlimited, except for the presence of contaminants on the
surface
8 4 3
Maximum Unlimited, except for the presence of contaminants on the
surface
Application
After adequate preparation of the surface, apply the product as follows: apply a coat of our SABBIAFOND white primer of the same tone as the finish with a brush or roller diluted with 20-25% water. To obtain a colour from our bundle, mix the quantity indicated on our PLATINUM LINE folder.Add and mix our TONER coloring pastes.
First coat: spread PERLA evenly undiluted with the appropriate plastic trowel, putting a good amount of product and smoothing until a smooth surface is obtained.
Second coat: after 4-5 hours, always apply a second coat with the appropriate plastic trowel, creating crossed spots from right to left from top to bottom, with gentle movements, thus creating the desired decoration.
First coat: spread PERLA evenly undiluted with the appropriate plastic trowel, putting a good amount of product and smoothing until a smooth surface is obtained.
Second coat: after 4-5 hours, always apply a second coat with the appropriate plastic trowel, creating crossed spots from right to left from top to bottom, with gentle movements, thus creating the desired decoration.
Shelf life
2 years in a cool and dry place (max 40°C)
Packs
Comp A Kg. 2 – Kg. 5.