code
0713
Description
Finish based on acrylic resins in water emulsion and special particle - size pigments with metal effect.
Use
This product can be applied to wall surfaces, properly prepared with concrete, where a metallescent aesthetic appearance combined with excellent resistance to washing with cleansing agents are required.
Appearance of the film
Metallescent
Color
Colour chart
Component
1
Hardening
Physical hardening through evaporation of water and union of the polymer
Specific weight
From 1,02 gr/m
VOC
40 gr/ liter
specific weight
50 -60 micron
Estimated yield
4 - 6 m² / kg for a thickness of 50 microns
Flash point
Component A > 114°C
Temperature Resistance
Max 60°C
Preparation of surfaces
New surfaces: apply a coat of our insulating product « IMPRIMITURA ACRILICA » diluted with water in ratio 1 to 5 (mix each liter of « IMPRIMITURA ACRILICA » with 5 liters of water).
Old surfaces: remove any parts that are peeling off and, after a careful cleaning of the substrate, apply a coat of our insulating product « IMPRIMITURA ACRILICA » diluted with water in ratio 1 to 5 (mix each liter of « IMPRIMITURA ACRILICA » with 5 liters of water).
Old surfaces: remove any parts that are peeling off and, after a careful cleaning of the substrate, apply a coat of our insulating product « IMPRIMITURA ACRILICA » diluted with water in ratio 1 to 5 (mix each liter of « IMPRIMITURA ACRILICA » with 5 liters of water).
Preparation of the product
Mix the product before the use and add water
Component A 100
Water 10 - 15 %
Component A 100
Water 10 - 15 %
Environmental conditions
Ambient temperature: from + 5 to 40° C
Temperature of the support: > 10° C
Humidity: 0 - 85 %
In order to prevent the formation of condensation, it is necessary that the temperature of the substrate is at least 3° C above the dew point
Temperature of the support: > 10° C
Humidity: 0 - 85 %
In order to prevent the formation of condensation, it is necessary that the temperature of the substrate is at least 3° C above the dew point
Drying and hardening time
For the thickness of 50 microns 10° C 20° C 30° C
Dry to touch 3 1 0,5 hours
Dry in depth 8 4 - 5 2 hours
Dry to touch 3 1 0,5 hours
Dry in depth 8 4 - 5 2 hours
Time of overpainting
Minimum (hours) 10° C 20° C 30° C
8 4 3 hours
Maximum unlimited in the absence of contaminants
8 4 3 hours
Maximum unlimited in the absence of contaminants
Application
After an appropriate preparation of the substrate, apply the product as follows: apply a coat of our white primer « SABBIAFOND » with brushes or roller diluted with water to 20 - 25 %.
First coat: apply « SETA » diluted with water to 10 - 15 % with a short - haired wool roller. Let it dry for about 3 hours.
Second coat: after 3 - 4 hours with a diluted product, apply a second coat, in a regular way, with a short - haired wool roller. Immediately afterwards, with the still wet substrate, work with the plastic trowel proceeding with continuous circular movements.
Third coat: after 3 - 4 hours with a diluted product, apply a third coat, in a regular way, with a short - haired roller. Immediately afterwards, work the substrate still wet with the plastic trowel proceeding with continuous circular movements.
First coat: apply « SETA » diluted with water to 10 - 15 % with a short - haired wool roller. Let it dry for about 3 hours.
Second coat: after 3 - 4 hours with a diluted product, apply a second coat, in a regular way, with a short - haired wool roller. Immediately afterwards, with the still wet substrate, work with the plastic trowel proceeding with continuous circular movements.
Third coat: after 3 - 4 hours with a diluted product, apply a third coat, in a regular way, with a short - haired roller. Immediately afterwards, work the substrate still wet with the plastic trowel proceeding with continuous circular movements.
Shelf life
2 years in a cool and dry place (max 40° C)
Packs
Comp A Kg. 2 – Kg. 5.